General Discussion     Tech Questions     Parts & Services     Suggestions/Ideas     Help & Website Instructions     Blogs    

Truck & Transportation History

Home Search Tags


Small cam injector tool

Posted By RobertMoen Monday, December 13, 2021 4:29 PM
Add to Favorites1
Author Message
RobertMoen
 Posted Monday, December 13, 2021 4:29 PM
.

. - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation)

Group: Forum User
Last Active: 2 days ago @ 4:21 PM
Posts: 12, Visits: 346
425
Hoping someone can tell me where to source the tool for actuation the injector rocker arm while setting non top stop injectors using the dial indicator method, I am not having much luck searching online.
Newto
 Posted Tuesday, December 14, 2021 9:35 AM
.

. - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation)

Group: Forum User
Last Active: Yesterday @ 3:17 PM
Posts: 149, Visits: 2,712
If they are non top stop injectors then the best method is to use an inch pound tension wrench and set them to 72 in/lbs on the outer base circle method...ie when the injector plunger is fully down and seated in the cup. Much more accurate than the dial indicator method which doesn't allow for any wear on the top of the cam lobe.

Cheers,

Newto
jimfols
 Posted Tuesday, December 14, 2021 11:42 AM
.

. - (29,819 reputation). - (29,819 reputation). - (29,819 reputation). - (29,819 reputation). - (29,819 reputation). - (29,819 reputation). - (29,819 reputation). - (29,819 reputation). - (29,819 reputation)

Group: Forum User
Last Active: Yesterday @ 1:12 PM
Posts: 97, Visits: 2,691
^^^^ What Newto said +1000

Over 60 Years of Service Dedicated to Trucking in America
PT Fuel Systems Forever

Jim
Newto
 Posted Wednesday, December 15, 2021 8:21 PM
.

. - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation)

Group: Forum User
Last Active: Yesterday @ 3:17 PM
Posts: 149, Visits: 2,712
:D
RobertMoen
 Posted Thursday, December 16, 2021 6:45 AM
.

. - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation). - (425 reputation)

Group: Forum User
Last Active: 2 days ago @ 4:21 PM
Posts: 12, Visits: 346
425
Thanks, going to be doing a pump and injectors and was a little paranoid about smashing the plungers into the cups if I didn't have it lined up just right so the dial indicator method looked a little safer🤣
Newto
 Posted Thursday, December 16, 2021 10:24 AM
.

. - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation). - (33,213 reputation)

Group: Forum User
Last Active: Yesterday @ 3:17 PM
Posts: 149, Visits: 2,712
there's more chance of getting it wrong with the dial indicator.....a few thou too tight and you WOULD be trying to push the plungers through the cups.....tension wrench sets the plunger to cup perfectly.....just remember to wind the adjusting screw down and back at least once before using the tension wrench so you purge any residual fuel out of the cup before tensioning.

Newto

Similar Topics

Expand / Collapse

Reading This Topic

Expand / Collapse

Back To Top